Threading: 1/2x36 is the most common thread type for 9mm muzzle devices, flash hiders, compensators, and muzzle brakes are made to match these threadings.įinish: Manganese Phosphate - Manganese Phosphate finishes are used on barrels to protect against corrosion and wear. Operators will still be required to change position to prevent the enemy from zeroing in. Those who engage in nighttime operations should be aware that no flash hider completely eliminates flash signature. Can significantly remove the flash from the end of your barrel. The A2 flash hider will redirect the flash to the side and away from the shooter's line of sight, thereby preserving night vision. A good flash hider, although not able to completely remove the flash effect. A2 Flash Hider is an effective option for reducing muzzle flash from AR-15 rifle barrels 1/2 - 28 threads 1.75 overall length the use of a crush washer is. Sometimes, there is remaining powder burnt causing the visible flash out of the end of your weapon. While modern day ARs and ammo are designed to burn as much gunpowder as possible, it doesnâ€™t always happen that way.

This muzzle device is designed to hide the flash of your rifle. Or even all three at once! Competitors who shoot in competition with Pistol Caliber Carbines love 9mm for its controllability, and even you can use a Muzzle Device with your next 9mm build to make it even better!Ībout This Muzzle Device: Flash Hider - A flash hider is exactly what it sounds like. Oncethe muzzle is uncorked, the gases are traveling at about 5700 fps and will pass the bullet.Picking the right muzzle device for your build is usually one of the last things to consider for a 9mm AR-15, however, you will be able to take the already easily manageable 9mm cartridge and make it even greater to wield with a muzzle device, allowing for faster follow up shots, reducing the recoil further, or extra flash hiding capabilities. The bullet exits the muzzle around 3000 fps, give or take. Crush washer recommended but not included. This high quality, steel phosphate, flash hider is ready for installation on your AR-15 rifle. In theory, the barrel should return after the shot, but what do you think? Should I ditch the compensator or is this nothing to worry about?A thicker diameter barrel will have less flex (barrel whip) than a thinner one. The AR-STONER A2 Flash Hider with 1/2' - 36 thread 9mm in Steel Phosphate is an effective option for reducing muzzle flash from AR-15 rifle barrels. The collar, which is twisted around the circumference of the flash hider, when. A flash suppressor is different from a muzzle brake, although they are typically mounted in the same position and sometimes confused with each other. The flash hider utilizes a locking collar that secures using an octagonal body. The AR-10 A2 Flash Hider is a cost effective, reliable and durable attachment that will meet and exceed the needs of any AR shooter. Last edited by trackmagic 04-23-13 at 23:50. Product Info for Noveske AR-10 A2 Flash Hider. In theory, the barrel should return after the shot, but what do you think? Should I ditch the compensator or is this nothing to worry about? If its pinned, this will typically allow you to easily remove the side with the pin - it might take a few taps with a hammer. When its split on both sides, you can use a flatbar to pry/split the device, leaving the barrel intact. The barrel without is being disturbed less for the one without the compensator The female threads are deeper than the male ones you wont damage the male threads on the barrel. Our 9mm A2 flash hider is machined from chromoly steel, finished in black phosphate, and includes a crush washer. (Just watch the end to see the barrel whip) Simple, light weight, and incredibly effective flash hider for your 9mm rifle. Here is a slow-motion video of a gun with a compensator: FLAT DARK EARTH CERAKOTE AR-15 A2 FLASH HIDER MUZZLE BRAKE, Flat dark earth cerakote FDE AR15 1/2x28 TPI A2 muzzle brake / flash hider, AR15 1/2x28 A2. I am wondering if the barrel whip will affect the follow-up shots. The flash-hider affecting the bullet does not make me worried (it should be gone before the gas gets to the flash hider), but I am worried about the compensation aspect of the A2 and barrel whip. I feel pretty good with everything I am putting on the gun except the A2 flash hider that I bought for $15. I have a match grade barrel, a FF hand guard is on order and I will put a 4-14X scope on it. My goal is to make an AR that will drive tacks. I am in the middle of building a new upper.

Ar a2 flash hider 2 in